* STRUCTURAL CONCRETE CRACK REPAIR SUPER KIT SealBoss 4000 Epoxy System 6 x 4000 LV Resin - 6 x 4000 Paste - 12 Cartridges, 12 Mixers, 1 Hand Gun

 

Professional

Structural Strength Epoxy Crack Cartridge Repair System

Repair Cracked Concrete

With SealBoss 4000 Line Structural Strength Epoxies 

 

 

This Commercial Grade Kit includes:

1 Epoxy Injection Handgun 2:1 mix-ratio
6 34oz SealBoss 4000slv Epoxy Injection Resin
6 34oz SealBoss 4000 Quickseal Epoxy Paste
6 Static Mixer Resin
6 Static Mixer Paste
1 Injection System Manual, Product Information
1 Pair Protective Latex Gloves

Injection Ports, Connectors and other Accessories sold separately

Toll Free Telephone Support, SealBoss Hotline 1877-932-2293

SealBoss 4000 LV Epoxy Adhesive & Injection Resin

RANGE OF APPLICATION

- Structural Repairs

- Crack Injection and Gravity Feed in concrete, masonry, etc.

- Structural Joint Repair

- Welding Cracked Concrete

- Bolt Grouting

- Plate Grouting

- Delaminated Slab Welding

- Repairing Wood Beams

 

TYPE OF MATERIAL

SealBoss® 4000 LV-Epoxy-Resin is a 100% solids, high modulus, low viscosity non-shrink two component epoxy resin that bonds to concrete and other surfaces.

4000 LV-Epoxy-Resin, Type I and II, Grade 2 Classes B and C for Epoxy Resin Adhesives.

4000 LV-Epoxy-Resin is an easy flow formulation for good penetration into cracks and voids even at lower injection pressures. The product is insensitive to moisture. Due to the high tensile and compressive strength of the cured product, 4000 LV-Epoxy-Resin is ideal for structural repairs.

PROCESSING

4000 LV-Epoxy-Resin is composed of two components. The mixing ratio by volume is 2:1 (A:B).

Using our cartridge system either with a hand operated trigger gun or a convenient pneumatic or electric battery operated gun makes the application easy and clean. No matter how much material is dispensed the design of the gun will assure the correct mixing ratio. If a cartridge is not used up the plastic mixer needs to be replaced prior to the next use. Minimum surface temperature is 40F. Do not add solvents to the product.

SealBoss 4000 QuickSeal Epoxy Adhesive Paste / Gel

 

 

 

 

 

 

 

 

RANGE OF APPLICATION

- Structural bonding of concrete, masonry, metals, wood, etc.

- Grouting bolts, dowels, pins, vertical and overhead, for extremely rapid setting, fast turn around times

- Seals cracks and around injection ports prior to pressure-injection grouting

- Interior, exterior, vertical and overhead repair of concrete as a super fast setting epoxy mortar binder.

ADVANTAGES

- Insensitive to moisture before, during and after cure

- High-modulus, high-strength, structural gel adhesive

- Excellent adhesion to concrete, masonry, metals, wood and most structural materials.

- Gel consistency ideal for vertical and overhead applications. Easy to mix 1: 1 ratio between components

- Extremely Fast Setting and high early strength-developing adhesive.TYPE OF MATERIAL

SealBoss ® 4000 QuickSeal  Epoxy Paste is a 100% solids, high modulus, non-sag, non-shrink two component epoxy adhesive that bonds to concrete and other surfaces.

It meets ASTM-C-881, Type I and IV, Grade 3 Classes B and C for Epoxy Resin Adhesives.PROCESSING

To anchor bolts, dowels and pins Annular space around bolt tested at 1/8 inch; depth of embedment is typically 10-15 times the bolt diameter. See cartridge for application instructions.To seal cracks for injection grouting

Place the mixed material over the cracks to be pressure injected and around each injection port. Allow sufficient time to cure before pressure injecting.As a structural adhesive

Apply the mixed 4000 QuickSeal-Epoxy Structural Gel Epoxy to the mating or non mating prepared substrates. Work into the substrate for positive adhesion. Secure the bonded unit firmly into place until the epoxy has cured.
Non-sag gel, no flow. Pot Life: Approx. 5-10 minutes. (100 gram mass)

Appearance: Compound A = White , Compound B = Grey.

Concrete Application Recommendations:

Surface Preparation:Surface must be clean and sound. It may be dry or damp, but free of standing water. Remove dust, grease, curing compounds, waxes, foreign particles and disintegrated materials.