Browse by Manufacturer
     Search By Manufacturer

Browse Categories
Mailing Lists
     Subscribe To Mailing List

SealBoss R70 Pump Flush, DOT non hazardous flush, 5 gal unit

<< Previous in Polyurethane Products Next in Polyurethane Products >>

Your Price: $173.99
Manufacturer: SealBoss Corp.

 
SealBoss ® Product Line:

Concrete Repair Products
Crack Injection Systems
Waterproofing Products
Joint Filler Compounds
Cartridge Systems
Specialty Coatings
Equipment & Accessories
SealBoss® provides commercial grade, professional quality
concrete repair
and waterproofing products, equipment and
accessories for
commercial and residential applications. 
 
 
 
5 Gal R70 Pump Flush for uses on:
 
SealBoss P1001
SealBoss P2002
SealBoss IP495
SealBoss PA3000
SealBoss JointMaster Pro2
 
 
- Many other single and multi-component joint filling and injection pumps.  Please call for more informatio at 877-932-2293
 

SealBoss R70 Pump Flush and Cleaner does not have a hazard class for shipping and is not considered flammable. It offers many advantages over solvents on the jobsite for health and safety purposes. R70 Pump Flush and Cleaner is less aggressive towards rubber and plastic parts than solvents and is safer for the pumping equipment. R70 Pump Flush and Cleaner non-drying poperties work as a lubricant.The maintenance and cleaning of your equipment is of the utmost importance to provide for safe workplace conditions.

 

Pumping epoxy resins and polyurethane injection foam grouts and resins, is like pumping a liquid glue – the product will eventually set up and clog the hoses and freeze the mechanical parts of your machine if you do not clean it out in time.

 

To rebuild a clogged-up injection machine can be very costly - or even impossible.

 

Important: Clean the machine thoroughly and frequently. The materials used for concrete injection are strong adhesives. Polyurethanes are water-activated.

 

Do not pump water with your grout injection pump.

Epoxies often have a short gel-time. Do not leave materials in the pump.

If in doubt of water residue in pump prior to use, flush first with a very small amount of SealBoss R70 Pump Flush and Cleaner or a solvent (not supplied by us) to eliminate moisture.

Caution: Xylol, Toluol, Acetone, M.E.K. are hazardous, combustible, aggressive towards the environment, equipment, seals and hoses. Omit solvent if in conflict with regulations on the jobsite or the equipment you use.

Do not leave material in the pump for an extended time.

Rule of thumb: If you don’t pump for more than twenty minutes purge the system and clean it.

Take the cleaning process seriously and spend the necessary time. The larger the pump and its capacity including suction tubes and pressure line the more time is takes and the more cleaning agent you need to use.


Toll Free Telephone Support, SealBoss Hotline 1877-932-2293

 
For more detailed product information please look at these links:
 
 
 
 
 
 
 
Satisfied Customer Testimonial

Michael P.
SealBoss. customer for D.I.Y. Kit
 
Craig,

Just wanted to say how glad I was to have your product on Monday. I live in Cobb County, GA and the water came pouring in during our recent flooding. I had already actually patched one of my two retaining wall cracks and already had the holes drilled for the second. However, I had not pumped the second one, so I got a desperate call from my wife for help when the rain hit that critical point and water stacks up against the front of our house. I got there from work as quickly as I could and still had to tighten the packers and mix the resin, but I had the water stopped inside of 15 minutes and we got nothing wet except for a few towels! What a lifesaver! There are a couple of areas that I just could not get the foam into so I am going to have to drill a few holes to make certain everything is sealed. I will need to order a few more more packers for that. I have bragged to many guys here at work about the DIY system and several have asked for your info for themselves or others, so I have passed your website along to quite a few already!

Thanks Again,

Michael
 
POLYURETHANE (PU)
CHARACTERISTICS:
EPOXY (EP)
- Flexible to semi-flexible sealants with little structural strength
- React to foams (water-stops), gels and solid (non cellular) flexible or semi flexible sealants.
- Classified as hydrophobic (foams/resins) for crack injection, joints voids or hydrophilic (foams/gels) for curtain, bladder injection behind structures. Both groups are water activated for use in wet environments - Superior water-stop capabilities
- Single or two component, accelerators common. Viscosities low to medium. Very resistant, long term solution.
SealBoss recommended Products:
Foams: 1510, 1570, 1572
Flexible resin: 1400 LV-Resin Line
Gel/Foam: Flexgel2
Conclusion: In non structural water related repairs PU is generally the material of choice. This is true for most below grade repairs including basements, tunnels, parking garages and manholes. EP is excellent for structural repairs of stressed structures and deteriorated concrete.
- Rigid, very strong adhesive for structural repairs in mainly dry environments, typically reduced adhesion on wet surfaces. Excellent to regain structural strength in torn structures: earthquake damage, extended stress damage
- Not a water-stop material and does not tolerate extended movement.
- Two component. Viscosities from very low to paste. Very resistant, long term solution.
SealBoss recommended Products:

Resin: 4040
Paste/Putty: 4000 Quickseal
Cartridge System: 4000 Epoxy Cartridge System
POLYURETHANE
APPLICATION TECHNIQUES:
EPOXY
- Mechanical packer injection at higher pressures 300-3000 psi
Reason: PU injection is often performed in a wet environment where adhesives for surface ports cannot be used. Mechanical packers are installed by drilling a hole into the structure which the packer fits snugly. The packer is tightened mechanically for high pressure injection. PU immediately reacts with moisture in the crack increasing resistance of product flow which explains the high injection pressures.
SealBoss recommended Products: Complete line of packers: S-Type, R-Type, custom sizes, Hammer-in packers, surface ports, specialty packers
Conclusion: PU generally needs higher pressures and therefor the more sophisticated connectors / packers. There are many exceptions. For example curtain injection with PU gel into the space between structure and soil needs lower injection pressures but higher rates of material flow. The filling of larger voids and joint injection also uses lower pressures. PU injection through surface ports is not common, but high pressure epoxy injection through packers is seen more frequently. Reasons could be very thick concrete to be penetrated or damp / wet surface conditions.
 

- Surface port injection at lower injection pressures 30-800psi
Reason: Injection is typically done in dry environments and surface ports can be attached easily with epoxy adhesive. Holes do not have to be drilled . However the crack surface between the ports has to be surface sealed to prevent leakage during injection. The viscosity of the epoxy resin stays low during the injection process, resulting in much lower injection pressures.
SealBoss recommended Products:
surface ports, specialty ports
POLYURETHANE
PUMPING TECHNIQUES / THE EQUIPMENT
EPOXY
- Single component equipment for most water-activated hydrophobic
PU foams, accelerator to be added prior to pumping.
- Either single or two component equipment for true two component
PU resins such as 1400 LV-Resin Line.
- Either single component or multi-ratio two component equipment
for hydrophilic PU Gels based on the application and product. In multi-ratio pumping one component carries a high water content.
Single component pumps include inexpensive hand held devices, hand pumps and electric pumps. Multi ratio devices can be manual, electric and pneumatic. Some PU injection pumps can be used for epoxy injection (with limitations). SealBoss supplies PU as small as 1 gal units. We do not supply PU in cartridges for the following reasons: 1. Reduced shelf life in cartridge due to high moisture sensitivity, 2. Limited Injection pressure. For small jobs we recommend our (3000psi) handgun and a 1 gallon unit.
SealBoss recommended Products:
Hand held guns, manual pump HP100, electric pumps IP395 Pro, P1001

Final Remarks: Injection Technology has become more refined and in cases more confusing. Modern products are very capable, but similar characteristics are not easily distinguished by the untrained person. To avoid costly failures caused by product/job mismatches, SealBoss provides thorough technical support to make your job a good one. Please make use of our services - we are just a phone call away.
- Two component equipment for most epoxy resins for ease of use and precise mixing.
- Single component equipment for small jobs and epoxy with longer gel-time. Observe gel time closely and clean equipment
thoroughly. Epoxy is a very strong adhesive and may render a pump unusable.
- Pneumatic or manual guns for cartridge systems / smaller jobs
Two component injection pumps are pneumatic or electric. SealBoss supplies EP resins and paste also in cartridges for the following reasons: 1. Ease of use, 2. Cost, 3. EP is not very moisture sensitive and injection pressures can be handled by quality cartridges and dispensers. Dispensers are manual or pneumatic. With very few exceptions EP pumps are not to be used for PU injection.
SealBoss recommended Products:
Hand held guns, pneumatic pump PA3000, 4000 Cartridge System

See More Related Products

* Pump SealBoss P2002 Drill Operated Injection Pump
Your Price: $1,599.00
* Pump SealBoss P2002 Drill Operated Injection Pump
SealBoss P2002 6000 PSI Drill Operated Single Component High Pressure Injection Pump (Hose Set included, Drill sold separately - see more images)
Pump SealBoss HP100 Single Component Pump
Your Price: Call For International Pricing
Pump SealBoss HP100 Single Component Pump
SealBoss HP 100 hand operated single component pump
Pump SealBoss IP2C Stainless Steel Acrylate Pump
Your Price: Call for Pricing
Pump SealBoss IP2C Stainless Steel Acrylate Pump
SealBoss IP2C DUAL COMPONENT POLYACRYLATE PUMP
Pump SealBoss IP495 Concrete Injection Pump
MSRP: $1,499.00
Your Price: Add to Cart to View Price
Pump SealBoss IP495 Concrete Injection Pump
IP 495 Pro Single Component Pump
Pump SealBoss JointMaster Pro2 Polyurea, Polyurethane, Epoxy Joint Filler Pump - SPECIAL OFFER
MSRP: $7,995.00
Your Price: $6,595.00
Online Savings: $1,400.00 (18 %)
Pump SealBoss JointMaster Pro2 Polyurea, Polyurethane, Epoxy Joint Filler Pump - SPECIAL OFFER
JOINTMASTER PRO2 IS A DUAL COMPONENT , 1:1 RATIO JOINT FILLING POLYUREA PUMP. CAN BE CONVERTED TO 2:1, PLEASE CALL FOR DETAILS AND SPECIAL OFFERS.
Pump SealBoss PA3000 Dual Component Epoxy Pump
Your Price: Special Starter Kit Options & Dealer Prices. Call us 877-932-2293 or 714-662-4445. Add to Cart for special limited online price
Pump SealBoss PA3000 Dual Component Epoxy Pump
SealBoss PA3000 DUAL COMPONENT EPOXY INJECTION PUMP. 2:1 RATIO WHICH CAN BE CHANGED TO 1:1 FOR ADDITIONAL COSTS. PLEASE CALL FOR DETAILS.

Product Reviews

(0 Ratings, 0 Reviews)
Shopping Cart
          Shopping Cart

Your cart is empty.